OpenRFC.org Requests For Comments ... for the community
Welcome to OpenRFC
Home Full RFC index RFC humour Our technology
 
RFC 4128
Bandwidth Constraints Models for Differentiated Services (Diffserv)-aware MPLS Traffic Engineering: Performance Evaluation.
W. Lai. June 2005.

 
[Direct link][Download PDF version][Download text version]
 

Network Working Group W. Lai Request for Comments: 4128 AT&T Labs Category: Informational June 2005 Bandwidth Constraints Models for Differentiated Services (Diffserv)-aware MPLS Traffic Engineering: Performance Evaluation Status of This Memo This memo provides information for the Internet community. It does not specify an Internet standard of any kind. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (2005). IESG Note The content of this RFC has been considered by the IETF (specifically in the TE-WG working group, which has no problem with publication as an Informational RFC), and therefore it may resemble a current IETF work in progress or a published IETF work. However, this document is an individual submission and not a candidate for any level of Internet Standard. The IETF disclaims any knowledge of the fitness of this RFC for any purpose, and in particular notes that it has not had complete IETF review for such things as security, congestion control or inappropriate interaction with deployed protocols. The RFC Editor has chosen to publish this document at its discretion. Readers of this RFC should exercise caution in evaluating its value for implementation and deployment. See RFC 3932 for more information. Abstract "Differentiated Services (Diffserv)-aware MPLS Traffic Engineering Requirements", RFC 3564, specifies the requirements and selection criteria for Bandwidth Constraints Models. Two such models, the Maximum Allocation and the Russian Dolls, are described therein. This document complements RFC 3564 by presenting the results of a performance evaluation of these two models under various operational conditions: normal load, overload, preemption fully or partially enabled, pure blocking, or complete sharing. Lai Standards Track [Page 1]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Table of Contents 1. Introduction ....................................................3 1.1. Conventions used in this document ..........................4 2. Bandwidth Constraints Models ....................................4 3. Performance Model ...............................................5 3.1. LSP Blocking and Preemption ................................6 3.2. Example Link Traffic Model .................................8 3.3. Performance under Normal Load ..............................9 4. Performance under Overload .....................................10 4.1. Bandwidth Sharing versus Isolation ........................10 4.2. Improving Class 2 Performance at the Expense of Class 3 ...12 4.3. Comparing Bandwidth Constraints of Different Models .......13 5. Performance under Partial Preemption ...........................15 5.1. Russian Dolls Model .......................................16 5.2. Maximum Allocation Model ..................................16 6. Performance under Pure Blocking ................................17 6.1. Russian Dolls Model .......................................17 6.2. Maximum Allocation Model ..................................18 7. Performance under Complete Sharing .............................19 8. Implications on Performance Criteria ...........................20 9. Conclusions ....................................................21 10. Security Considerations .......................................22 11. Acknowledgements ..............................................22 12. References ....................................................22 12.1. Normative References ....................................22 12.2. Informative References ..................................22 Lai Standards Track [Page 2]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 1. Introduction Differentiated Services (Diffserv)-aware MPLS Traffic Engineering (DS-TE) mechanisms operate on the basis of different Diffserv classes of traffic to improve network performance. Requirements for DS-TE and the associated protocol extensions are specified in references [1] and [2] respectively. To achieve per-class traffic engineering, rather than on an aggregate basis across all classes, DS-TE enforces different Bandwidth Constraints (BCs) on different classes. Reference [1] specifies the requirements and selection criteria for Bandwidth Constraints Models (BCMs) for the purpose of allocating bandwidth to individual classes. This document presents a performance analysis for the two BCMs described in [1]: (1) Maximum Allocation Model (MAM) - the maximum allowable bandwidth usage of each class, together with the aggregate usage across all classes, are explicitly specified. (2) Russian Dolls Model (RDM) - specification of maximum allowable usage is done cumulatively by grouping successive priority classes recursively. The following criteria are also listed in [1] for investigating the performance and trade-offs of different operational aspects of BCMs: (1) addresses the scenarios in Section 2 of [1] (2) works well under both normal and overload conditions (3) applies equally when preemption is either enabled or disabled (4) minimizes signaling load processing requirements (5) maximizes efficient use of the network (6) minimizes implementation and deployment complexity The use of any given BCM has significant impacts on the capability of a network to provide protection for different classes of traffic, particularly under high load, so that performance objectives can be met [3]. This document complements [1] by presenting the results of a performance evaluation of the above two BCMs under various operational conditions: normal load, overload, preemption fully or partially enabled, pure blocking, or complete sharing. Thus, our focus is only on the performance-oriented criteria and their Lai Standards Track [Page 3]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 implications for a network implementation. In other words, we are only concerned with criteria (2), (3), and (5); we will not address criteria (1), (4), or (6). Related documents in this area include [4], [5], [6], [7], and [8]. In the rest of this document, the following DS-TE acronyms are used: BC Bandwidth Constraint BCM Bandwidth Constraints Model MAM Maximum Allocation Model RDM Russian Dolls Model There may be differences between the quality of service expressed and obtained with Diffserv without DS-TE and with DS-TE. Because DS-TE uses Constraint Based Routing, and because of the type of admission control capabilities it adds to Diffserv, DS-TE has capabilities for traffic that Diffserv does not. Diffserv does not indicate preemption, by intent, whereas DS-TE describes multiple levels of preemption for its Class-Types. Also, Diffserv does not support any means of explicitly controlling overbooking, while DS-TE allows this. When considering a complete quality of service environment, with Diffserv routers and DS-TE, it is important to consider these differences carefully. 1.1. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119. 2. Bandwidth Constraints Models To simplify our presentation, we use the informal name "class of traffic" for the terms Class-Type and TE-Class, defined in [1]. We assume that (1) there are only three classes of traffic, and that (2) all label-switched paths (LSPs), regardless of class, require the same amount of bandwidth. Furthermore, the focus is on the bandwidth usage of an individual link with a given capacity; routing aspects of LSP setup are not considered. The concept of reserved bandwidth is also defined in [1] to account for the possible use of overbooking. Rather than get into these details, we assume that each LSP is allocated 1 unit of bandwidth on a given link after establishment. This allows us to express link bandwidth usage simply in terms of the number of simultaneously established LSPs. Link capacity can then be used as the aggregate constraint on bandwidth usage across all classes. Lai Standards Track [Page 4]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Suppose that the three classes of traffic assumed above for the purposes of this document are denoted by class 1 (highest priority), class 2, and class 3 (lowest priority). When preemption is enabled, these are the preemption priorities. To define a generic class of BCMs for the purpose of our analysis in accordance with the above assumptions, let Nmax = link capacity; i.e., the maximum number of simultaneously established LSPs for all classes together Nc = the number of simultaneously established class c LSPs, for c = 1, 2, and 3, respectively. For MAM, let Bc = maximum number of simultaneously established class c LSPs. Then, Bc is the Bandwidth Constraint for class c, and we have Nc <= Bc <= Nmax, for c = 1, 2, and 3 N1 + N2 + N3 <= Nmax B1 + B2 + B3 >= Nmax For RDM, the BCs are specified as: B1 = maximum number of simultaneously established class 1 LSPs B2 = maximum number of simultaneously established LSPs for classes 1 and 2 together B3 = maximum number of simultaneously established LSPs for classes 1, 2, and 3 together Then, we have the following relationships: N1 <= B1 N1 + N2 <= B2 N1 + N2 + N3 <= B3 B1 < B2 < B3 = Nmax 3. Performance Model Reference [8] presents a 3-class Markov-chain performance model to analyze a general class of BCMs. The BCMs that can be analyzed include, besides MAM and RDM, BCMs with privately reserved bandwidth that cannot be preempted by other classes. Lai Standards Track [Page 5]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 The Markov-chain performance model in [8] assumes Poisson arrivals for LSP requests with exponentially distributed lifetime. The Poisson assumption for LSP requests is relevant since we are not dealing with the arrivals of individual packets within an LSP. Also, LSP lifetime may exhibit heavy-tail characteristics. This effect should be accounted for when the performance of a particular BCM by itself is evaluated. As the effect would be common for all BCMs, we ignore it for simplicity in the comparative analysis of the relative performance of different BCMs. In principle, a suitably chosen hyperexponential distribution may be used to capture some aspects of heavy tail. However, this will significantly increase the complexity of the non-product-form preemption model in [8]. The model in [8] assumes the use of admission control to allocate link bandwidth to LSPs of different classes in accordance with their respective BCs. Thus, the model accepts as input the link capacity and offered load from different classes. The blocking and preemption probabilities for different classes under different BCs are generated as output. Thus, from a service provider's perspective, given the desired level of blocking and preemption performance, the model can be used iteratively to determine the corresponding set of BCs. To understand the implications of using criteria (2), (3), and (5) in the Introduction Section to select a BCM, we present some numerical results of the analysis in [8]. This is intended to facilitate discussion of the issues that can arise. The major performance objective is to achieve a balance between the need for bandwidth sharing (for increasing bandwidth efficiency) and the need for bandwidth isolation (for protecting bandwidth access by different classes). 3.1. LSP Blocking and Preemption As described in Section 2, the three classes of traffic used as an example are class 1 (highest priority), class 2, and class 3 (lowest priority). Preemption may or may not be used, and we will examine the performance of each scenario. When preemption is used, the priorities are the preemption priorities. We consider cross-class preemption only, with no within-class preemption. In other words, preemption is enabled so that, when necessary, class 1 can preempt class 3 or class 2 (in that order), and class 2 can preempt class 3. Each class offers a load of traffic to the network that is expressed in terms of the arrival rate of its LSP requests and the average lifetime of an LSP. A unit of such a load is an erlang. (In packet-based networks, traffic volume is usually measured by counting the number of bytes and/or packets that are sent or received over an interface during a measurement period. Here we are only concerned Lai Standards Track [Page 6]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 with bandwidth allocation and usage at the LSP level. Therefore, as a measure of resource utilization in a link-speed independent manner, the erlang is an appropriate unit for our purpose [9].) To prevent Diffserv QoS degradation at the packet level, the expected number of established LSPs for a given class should be kept in line with the average service rate that the Diffserv scheduler can provide to that class. Because of the use of overbooking, the actual traffic carried by a link may be higher than expected, and hence QoS degradation may not be totally avoidable. However, the use of admission control at the LSP level helps minimize QoS degradation by enforcing the BCs established for the different classes, according to the rules of the BCM adopted. That is, the BCs are used to determine the number of LSPs that can be simultaneously established for different classes under various operational conditions. By controlling the number of LSPs admitted from different classes, this in turn ensures that the amount of traffic submitted to the Diffserv scheduler is compatible with the targeted packet-level QoS objectives. The performance of a BCM can therefore be measured by how well the given BCM handles the offered traffic, under normal or overload conditions, while maintaining packet-level service objectives. Thus, assuming that the enforcement of Diffserv QoS objectives by admission control is a given, the performance of a BCM can be expressed in terms of LSP blocking and preemption probabilities. Different BCMs have different strengths and weaknesses. Depending on the BCs chosen for a given load, a BCM may perform well in one operating region and poorly in another. Service providers are mainly concerned with the utility of a BCM to meet their operational needs. Regardless of which BCM is deployed, the foremost consideration is that the BCM works well under the engineered load, such as the ability to deliver service-level objectives for LSP blocking probabilities. It is also expected that the BCM handles overload "reasonably" well. Thus, for comparison, the common operating point we choose for BCMs is that they meet specified performance objectives in terms of blocking/preemption under given normal load. We then observe how their performance varies under overload. More will be said about this aspect later in Section 4.2. Lai Standards Track [Page 7]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 3.2. Example Link Traffic Model For example, consider a link with a capacity that allows a maximum of 15 LSPs from different classes to be established simultaneously. All LSPs are assumed to have an average lifetime of 1 time unit. Suppose that this link is being offered a load of 2.7 erlangs from class 1, 3.5 erlangs from class 2, and 3.5 erlangs from class 3. We now consider a scenario wherein the blocking/preemption performance objectives for the three classes are desired to be comparable under normal conditions (other scenarios are covered in later sections). To meet this service requirement under the above given load, the BCs are selected as follows: For MAM: up to 6 simultaneous LSPs for class 1, up to 7 simultaneous LSPs for class 2, and up to 15 simultaneous LSPs for class 3. For RDM: up to 6 simultaneous LSPs for class 1 by itself, up to 11 simultaneous LSPs for classes 1 and 2 together, and up to 15 simultaneous LSPs for all three classes together. Note that the driver is service requirement, independent of BCM. The above BCs are not picked arbitrarily; they are chosen to meet specific performance objectives in terms of blocking/preemption (detailed in the next section). An intuitive "explanation" for the above set of BCs may be as follows. Class 1 BC is the same (6) for both models, as class 1 is treated the same way under either model with preemption. However, MAM and RDM operate in fundamentally different ways and give different treatments to classes with lower preemption priorities. It can be seen from Section 2 that although RDM imposes a strict ordering of the different BCs (B1 < B2 < B3) and a hard boundary (B3 = Nmax), MAM uses a soft boundary (B1+B2+B3 >= Nmax) with no specific ordering. As will be explained in Section 4.3, this allows RDM to have a higher degree of sharing among different classes. Such a higher degree of coupling means that the numerical values of the BCs can be relatively smaller than those for MAM, to meet given performance requirements under normal load. Lai Standards Track [Page 8]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Thus, in the above example, the RDM BCs of (6, 11, 15) may be thought of as roughly corresponding to the MAM BCs of (6, 6+7, 6+7+15). (The intent here is just to point out that the design parameters for the two BCMs need to be different, as they operate differently; strictly speaking, the numerical correspondence is incorrect.) Of course, both BCMs are bounded by the same aggregate constraint of the link capacity (15). The BCs chosen in the above example are not intended to be regarded as typical values used by any service provider. They are used here mainly for illustrative purposes. The method we used for analysis can easily accommodate another set of parameter values as input. 3.3. Performance under Normal Load In the example above, based on the BCs chosen, the blocking and preemption probabilities for LSP setup requests under normal conditions for the two BCMs are given in Table 1. Remember that the BCs have been selected for this scenario to address the service requirement to offer comparable blocking/preemption objectives for the three classes. Table 1. Blocking and preemption probabilities BCM PB1 PB2 PB3 PP2 PP3 PB2+PP2 PB3+PP3 MAM 0.03692 0.03961 0.02384 0 0.02275 0.03961 0.04659 RDM 0.03692 0.02296 0.02402 0.01578 0.01611 0.03874 0.04013 In the above table, the following apply: PB1 = blocking probability of class 1 PB2 = blocking probability of class 2 PB3 = blocking probability of class 3 PP2 = preemption probability of class 2 PP3 = preemption probability of class 3 PB2+PP2 = combined blocking/preemption probability of class 2 PB3+PP3 = combined blocking/preemption probability of class 3 First, we observe that, indeed, the values for (PB1, PB2+PP2, PB3+PP3) are very similar one to another. This confirms that the service requirement (of comparable blocking/preemption objectives for the three classes) has been met for both BCMs. Lai Standards Track [Page 9]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Then, we observe that the (PB1, PB2+PP2, PB3+PP3) values for MAM are very similar to the (PB1, PB2+PP2, PB3+PP3) values for RDM. This indicates that, in this scenario, both BCMs offer very similar performance under normal load. From column 2 of Table 1, it can be seen that class 1 sees exactly the same blocking under both BCMs. This should be obvious since both allocate up to 6 simultaneous LSPs for use by class 1 only. Slightly better results are obtained from RDM, as shown by the last two columns in Table 1. This comes about because the cascaded bandwidth separation in RDM effectively gives class 3 some form of protection from being preempted by higher-priority classes. Also, note that PP2 is zero in this particular case, simply because the BCs for MAM happen to have been chosen in such a way that class 1 never has to preempt class 2 for any of the bandwidth that class 1 needs. (This is because class 1 can, in the worst case, get all the bandwidth it needs simply by preempting class 3 alone.) In general, this will not be the case. It is interesting to compare these results with those for the case of a single class. Based on the Erlang loss formula, a capacity of 15 servers can support an offered load of 10 erlangs with a blocking probability of 0.0364969. Whereas the total load for the 3-class BCM is less with 2.7 + 3.5 + 3.5 = 9.7 erlangs, the probabilities of blocking/preemption are higher. Thus, there is some loss of efficiency due to the link bandwidth being partitioned to accommodate for different traffic classes, thereby resulting in less sharing. This aspect will be examined in more detail later, in Section 7 on Complete Sharing. 4. Performance under Overload Overload occurs when the traffic on a system is greater than the traffic capacity of the system. To investigate the performance under overload conditions, the load of each class is varied separately. Blocking and preemption probabilities are not shown separately for each case; they are added together to yield a combined blocking/preemption probability. 4.1. Bandwidth Sharing versus Isolation Figures 1 and 2 show the relative performance when the load of each class in the example of Section 3.2 is varied separately. The three series of data in each of these figures are, respectively, Lai Standards Track [Page 10]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 class 1 blocking probability ("Class 1 B"), class 2 blocking/preemption probability ("Class 2 B+P"), and class 3 blocking/preemption probability ("Class 3 B+P"). For each of these series, the first set of four points is for the performance when class 1 load is increased from half of its normal load to twice its normal. Similarly, the next and the last sets of four points are when class 2 and class 3 loads are increased correspondingly. The following observations apply to both BCMs: 1. The performance of any class generally degrades as its load increases. 2. The performance of class 1 is not affected by any changes (increases or decreases) in either class 2 or class 3 traffic, because class 1 can always preempt others. 3. Similarly, the performance of class 2 is not affected by any changes in class 3 traffic. 4. Class 3 sees better (worse) than normal performance when either class 1 or class 2 traffic is below (above) normal. In contrast, the impact of the changes in class 1 traffic on class 2 performance is different for the two BCMs: It is negligible in MAM and significant in RDM. 1. Although class 2 sees little improvement (no improvement in this particular example) in performance when class 1 traffic is below normal when MAM is used, it sees better than normal performance under RDM. 2. Class 2 sees no degradation in performance when class 1 traffic is above normal when MAM is used. In this example, with BCs 6 + 7 < 15, class 1 and class 2 traffic is effectively being served by separate pools. Therefore, class 2 sees no preemption, and only class 3 is being preempted whenever necessary. This fact is confirmed by the Erlang loss formula: a load of 2.7 erlangs offered to 6 servers sees a 0.03692 blocking, and a load of 3.5 erlangs offered to 7 servers sees a 0.03961 blocking. These blocking probabilities are exactly the same as the corresponding entries in Table 1: PB1 and PB2 for MAM. 3. This is not the case in RDM. Here, the probability for class 2 to be preempted by class 1 is nonzero because of two effects. (1) Through the cascaded bandwidth arrangement, class 3 is protected Lai Standards Track [Page 11]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 somewhat from preemption. (2) Class 2 traffic is sharing a BC with class 1. Consequently, class 2 suffers when class 1 traffic increases. Thus, it appears that although the cascaded bandwidth arrangement and the resulting bandwidth sharing makes RDM work better under normal conditions, such interaction makes it less effective to provide class isolation under overload conditions. 4.2. Improving Class 2 Performance at the Expense of Class 3 We now consider a scenario in which the service requirement is to give better blocking/preemption performance to class 2 than to class 3, while maintaining class 1 performance at the same level as in the previous scenario. (The use of minimum deterministic guarantee for class 3 is to be considered in the next section.) So that the specified class 2 performance objective can be met, class 2 BC is increased appropriately. As an example, BCs (6, 9, 15) are now used for MAM, and (6, 13, 15) for RDM. For both BCMs, as shown in Figures 1bis and 2bis, although class 1 performance remains unchanged, class 2 now receives better performance, at the expense of class 3. This is of course due to the increased access of bandwidth by class 2 over class 3. Under normal conditions, the performance of the two BCMs is similar in terms of their blocking and preemption probabilities for LSP setup requests, as shown in Table 2. Table 2. Blocking and preemption probabilities BCM PB1 PB2 PB3 PP2 PP3 PB2+PP2 PB3+PP3 MAM 0.03692 0.00658 0.02733 0 0.02709 0.00658 0.05441 RDM 0.03692 0.00449 0.02759 0.00272 0.02436 0.00721 0.05195 Under overload, the observations in Section 4.1 regarding the difference in the general behavior between the two BCMs still apply, as shown in Figures 1bis and 2bis. The following are two frequently asked questions about the operation of BCMs. (1) For a link capacity of 15, would a class 1 BC of 6 and a class 2 BC of 9 in MAM result in the possibility of a total lockout for class 3? This will certainly be the case when there are 6 class 1 and 9 class 2 LSPs being established simultaneously. Such an offered load (with 6 class 1 and 9 class 2 LSP requests) will not cause a lockout of class 3 with RDM having a BC of 13 for classes 1 and 2 combined, but Lai Standards Track [Page 12]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 will result in class 2 LSPs being rejected. If class 2 traffic were considered relatively more important than class 3 traffic, then RDM would perform very poorly compared to MAM with BCs of (6, 9, 15). (2) Should MAM with BCs of (6, 7, 15) be used instead so as to make the performance of RDM look comparable? The answer is that the above scenario is not very realistic when the offered load is assumed to be (2.7, 3.5, 3.5) for the three classes, as stated in Section 3.2. Treating an overload of (6, 9, x) as a normal operating condition is incompatible with the engineering of BCs according to needed bandwidth from different classes. It would be rare for a given class to need so much more than its engineered bandwidth level. But if the class did, the expectation based on design and normal traffic fluctuations is that this class would quickly release unneeded bandwidth toward its engineered level, freeing up bandwidth for other classes. Service providers engineer their networks based on traffic projections to determine network configurations and needed capacity. All BCMs should be designed to operate under realistic network conditions. For any BCM to work properly, the selection of values for different BCs must therefore be based on the projected bandwidth needs of each class, as well as on the bandwidth allocation rules of the BCM itself. This is to ensure that the BCM works as expected under the intended design conditions. In operation, the actual load may well turn out to be different from that of the design. Thus, an assessment of the performance of a BCM under overload is essential to see how well the BCM can cope with traffic surges or network failures. Reflecting this view, the basis for comparison of two BCMs is that they meet the same or similar performance requirements under normal conditions, and how they withstand overload. In operational practice, load measurement and forecast would be useful to calibrate and fine-tune the BCs so that traffic from different classes could be redistributed accordingly. Dynamic adjustment of the Diffserv scheduler could also be used to minimize QoS degradation. 4.3. Comparing Bandwidth Constraints of Different Models As is pointed out in Section 3.2, the higher degree of sharing among the different classes in RDM means that the numerical values of the BCs could be relatively smaller than those for MAM. We now examine this aspect in more detail by considering the following scenario. We set the BCs so that (1) for both BCMs, the same value is used for class 1, (2) the same minimum deterministic guarantee of bandwidth for class 3 is offered by both BCMs, and (3) the blocking/preemption Lai Standards Track [Page 13]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 probability is minimized for class 2. We want to emphasize that this may not be the way service providers select BCs. It is done here to investigate the statistical behavior of such a deterministic mechanism. For illustration, we use BCs (6, 7, 15) for MAM, and (6, 13, 15) for RDM. In this case, both BCMs have 13 units of bandwidth for classes 1 and 2 together, and dedicate 2 units of bandwidth for use by class 3 only. The performance of the two BCMs under normal conditions is shown in Table 3. It is clear that MAM with (6, 7, 15) gives fairly comparable performance objectives across the three classes, whereas RDM with (6, 13, 15) strongly favors class 2 at the expense of class 3. They therefore cater to different service requirements. Table 3. Blocking and preemption probabilities BCM PB1 PB2 PB3 PP2 PP3 PB2+PP2 PB3+PP3 MAM 0.03692 0.03961 0.02384 0 0.02275 0.03961 0.04659 RDM 0.03692 0.00449 0.02759 0.00272 0.02436 0.00721 0.05195 By comparing Figures 1 and 2bis, it can be seen that, when being subjected to the same set of BCs, RDM gives class 2 much better performance than MAM, with class 3 being only slightly worse. This confirms the observation in Section 3.2 that, when the same service requirements under normal conditions are to be met, the numerical values of the BCs for RDM can be relatively smaller than those for MAM. This should not be surprising in view of the hard boundary (B3 = Nmax) in RDM versus the soft boundary (B1+B2+B3 >= Nmax) in MAM. The strict ordering of BCs (B1 < B2 < B3) gives RDM the advantage of a higher degree of sharing among the different classes; i.e., the ability to reallocate the unused bandwidth of higher-priority classes to lower-priority ones, if needed. Consequently, this leads to better performance when an identical set of BCs is used as exemplified above. Such a higher degree of sharing may necessitate the use of minimum deterministic bandwidth guarantee to offer some protection for lower-priority traffic from preemption. The explicit lack of ordering of BCs in MAM and its soft boundary imply that the use of minimum deterministic guarantees for lower- priority classes may not need to be enforced when there is a lesser degree of sharing. This is demonstrated by the example in Section 4.2 with BCs (6, 9, 15) for MAM. For illustration, Table 4 shows the performance under normal conditions of RDM with BCs (6, 15, 15). Lai Standards Track [Page 14]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Table 4. Blocking and preemption probabilities BCM PB1 PB2 PB3 PP2 PP3 PB2+PP2 PB3+PP3 RDM 0.03692 0.00060 0.02800 0.00032 0.02740 0.00092 0.05540 Regardless of whether deterministic guarantees are used, both BCMs are bounded by the same aggregate constraint of the link capacity. Also, in both BCMs, bandwidth access guarantees are necessarily achieved statistically because of traffic fluctuations, as explained in Section 4.2. (As a result, service-level objectives are typically specified as monthly averages, under the use of statistical guarantees rather than deterministic guarantees.) Thus, given the fundamentally different operating principles of the two BCMs (ordering, hard versus soft boundary), the dimensions of one BCM should not be adopted to design for the other. Rather, it is the service requirements, and perhaps also the operational needs, of a service provider that should be used to drive how the BCs of a BCM are selected. 5. Performance under Partial Preemption In the previous two sections, preemption is fully enabled in the sense that class 1 can preempt class 3 or class 2 (in that order), and class 2 can preempt class 3. That is, both classes 1 and 2 are preemptor-enabled, whereas classes 2 and 3 are preemptable. A class that is preemptor-enabled can preempt lower-priority classes designated as preemptable. A class not designated as preemptable cannot be preempted by any other classes, regardless of relative priorities. We now consider the three cases shown in Table 5, in which preemption is only partially enabled. Table 5. Partial preemption modes preemption modes preemptor-enabled preemptable "1+2 on 3" (Fig. 3, 6) class 1, class 2 class 3 "1 on 3" (Fig. 4, 7) class 1 class 3 "1 on 2+3" (Fig. 5, 8) class 1 class 3, class 2 In this section, we evaluate how these preemption modes affect the performance of a particular BCM. Thus, we are comparing how a given BCM performs when preemption is fully enabled versus how the same BCM performs when preemption is partially enabled. The performance of these preemption modes is shown in Figures 3 to 5 for RDM, and in Figures 6 through 8 for MAM, respectively. In all of these figures, Lai Standards Track [Page 15]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 the BCs of Section 3.2 are used for illustration; i.e., (6, 7, 15) for MAM and (6, 11, 15) for RDM. However, the general behavior is similar when the BCs are changed to those in Sections 4.2 and 4.3; i.e., (6, 9, 15) and (6, 13, 15), respectively. 5.1. Russian Dolls Model Let us first examine the performance under RDM. There are two sets of results, depending on whether class 2 is preemptable: (1) Figures 3 and 4 for the two modes when only class 3 is preemptable, and (2) Figure 2 in the previous section and Figure 5 for the two modes when both classes 2 and 3 are preemptable. By comparing these two sets of results, the following impacts can be observed. Specifically, when class 2 is non-preemptable, the behavior of each class is as follows: 1. Class 1 generally sees a higher blocking probability. As the class 1 space allocated by the class 1 BC is shared with class 2, which is now non-preemptable, class 1 cannot reclaim any such space occupied by class 2 when needed. Also, class 1 has less opportunity to preempt, as it is able to preempt class 3 only. 2. Class 3 also sees higher blocking/preemption when its own load is increased, as it is being preempted more frequently by class 1, when class 1 cannot preempt class 2. (See the last set of four points in the series for class 3 shown in Figures 3 and 4, when comparing with Figures 2 and 5.) 3. Class 2 blocking/preemption is reduced even when its own load is increased, since it is not being preempted by class 1. (See the middle set of four points in the series for class 2 shown in Figures 3 and 4, when comparing with Figures 2 and 5.) Another two sets of results are related to whether class 2 is preemptor-enabled. In this case, when class 2 is not preemptor- enabled, class 2 blocking/preemption is increased when class 3 load is increased. (See the last set of four points in the series for class 2 shown in Figures 4 and 5, when comparing with Figures 2 and 3.) This is because both classes 2 and 3 are now competing independently with each other for resources. 5.2. Maximum Allocation Model Turning now to MAM, the significant impact appears to be only on class 2, when it cannot preempt class 3, thereby causing its blocking/preemption to increase in two situations. Lai Standards Track [Page 16]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 1. When class 1 load is increased. (See the first set of four points in the series for class 2 shown in Figures 7 and 8, when comparing with Figures 1 and 6.) 2. When class 3 load is increased. (See the last set of four points in the series for class 2 shown in Figures 7 and 8, when comparing with Figures 1 and 6.) This is similar to RDM; i.e., class 2 and class 3 are now competing with each other. When Figure 1 (for the case of fully enabled preemption) is compared to Figures 6 through 8 (for partially enabled preemption), it can be seen that the performance of MAM is relatively insensitive to the different preemption modes. This is because when each class has its own bandwidth access limits, the degree of interference among the different classes is reduced. This is in contrast with RDM, whose behavior is more dependent on the preemption mode in use. 6. Performance under Pure Blocking This section covers the case in which preemption is completely disabled. We continue with the numerical example used in the previous sections, with the same link capacity and offered load. 6.1. Russian Dolls Model For RDM, we consider two different settings: "Russian Dolls (1)" BCs: up to 6 simultaneous LSPs for class 1 by itself, up to 11 simultaneous LSPs for classes 1 and 2 together, and up to 15 simultaneous LSPs for all three classes together. "Russian Dolls (2)" BCs: up to 9 simultaneous LSPs for class 3 by itself, up to 14 simultaneous LSPs for classes 3 and 2 together, and up to 15 simultaneous LSPs for all three classes together. Note that the "Russian Dolls (1)" set of BCs is the same as previously with preemption enabled, whereas the "Russian Dolls (2)" has the cascade of bandwidth arranged in reverse order of the classes. Lai Standards Track [Page 17]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 As observed in Section 4, the cascaded bandwidth arrangement is intended to offer lower-priority traffic some protection from preemption by higher-priority traffic. This is to avoid starvation. In a pure blocking environment, such protection is no longer necessary. As depicted in Figure 9, it actually produces the opposite, undesirable effect: higher-priority traffic sees higher blocking than lower-priority traffic. With no preemption, higher- priority traffic should be protected instead to ensure that it could get through when under high load. Indeed, when the reverse cascade is used in "Russian Dolls (2)", the required performance of lower blocking for higher-priority traffic is achieved, as shown in Figure 10. In this specific example, there is very little difference among the performance of the three classes in the first eight data points for each of the three series. However, the BCs can be tuned to get a bigger differentiation. 6.2. Maximum Allocation Model For MAM, we also consider two different settings: "Exp. Max. Alloc. (1)" BCs: up to 7 simultaneous LSPs for class 1, up to 8 simultaneous LSPs for class 2, and up to 8 simultaneous LSPs for class 3. "Exp. Max. Alloc. (2)" BCs: up to 7 simultaneous LSPs for class 1, with additional bandwidth for 1 LSP privately reserved up to 8 simultaneous LSPs for class 2, and up to 8 simultaneous LSPs for class 3. These BCs are chosen so that, under normal conditions, the blocking performance is similar to all the previous scenarios. The only difference between these two sets of values is that the "Exp. Max. Alloc. (2)" algorithm gives class 1 a private pool of 1 server for class protection. As a result, class 1 has a relatively lower blocking especially when its traffic is above normal, as can be seen by comparing Figures 11 and 12. This comes, of course, with a slight increase in the blocking of classes 2 and 3 traffic. When comparing the "Russian Dolls (2)" in Figure 10 with MAM in Figures 11 or 12, the difference between their behavior and the associated explanation are again similar to the case when preemption is used. The higher degree of sharing in the cascaded bandwidth arrangement of RDM leads to a tighter coupling between the different classes of traffic when under overload. Their performance therefore Lai Standards Track [Page 18]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 tends to degrade together when the load of any one class is increased. By imposing explicit maximum bandwidth usage on each class individually, better class isolation is achieved. The trade- off is that, generally, blocking performance in MAM is somewhat higher than in RDM, because of reduced sharing. The difference in the behavior of RDM with or without preemption has already been discussed at the beginning of this section. For MAM, some notable differences can also be observed from a comparison of Figures 1 and 11. If preemption is used, higher-priority traffic tends to be able to maintain its performance despite the overloading of other classes. This is not so if preemption is not allowed. The trade-off is that, generally, the overloaded class sees a relatively higher blocking/preemption when preemption is enabled than there would be if preemption is disabled. 7. Performance under Complete Sharing As observed towards the end of Section 3, the partitioning of bandwidth capacity for access by different traffic classes tends to reduce the maximum link efficiency achievable. We now consider the case where there is no such partitioning, thereby resulting in full sharing of the total bandwidth among all the classes. This is referred to as the Complete Sharing Model. For MAM, this means that the BCs are such that up to 15 simultaneous LSPs are allowed for any class. Similarly, for RDM, the BCs are up to 15 simultaneous LSPs for class 1 by itself, up to 15 simultaneous LSPs for classes 1 and 2 together, and up to 15 simultaneous LSPs for all three classes together. Effectively, there is now no distinction between MAM and RDM. Figure 13 shows the performance when all classes have equal access to link bandwidth under Complete Sharing. With preemption being fully enabled, class 1 sees virtually no blocking, regardless of the loading conditions of the link. Since class 2 can only preempt class 3, class 2 sees some blocking and/or preemption when either class 1 load or its own load is above normal; otherwise, class 2 is unaffected by increases of class 3 load. As higher priority classes always preempt class 3 when the link is full, class 3 suffers the most, with high blocking/preemption when there is any load increase from any class. A comparison of Figures 1, 2, and 13 shows that, although the performance of both classes 1 and 2 is far superior under Complete Sharing, class 3 performance is much Lai Standards Track [Page 19]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 better off under either MAM or RDM. In a sense, class 3 is starved under overload as no protection of its traffic is being provided under Complete Sharing. 8. Implications on Performance Criteria Based on the previous results, a general theme is shown to be the trade-off between bandwidth sharing and class protection/isolation. To show this more concretely, let us compare the different BCMs in terms of the overall loss probability. This quantity is defined as the long-term proportion of LSP requests from all classes combined that are lost as a result of either blocking or preemption, for a given level of offered load. As noted in the previous sections, although RDM has a higher degree of sharing than MAM, both ultimately converge to the Complete Sharing Model as the degree of sharing in each of them is increased. Figure 14 shows that, for a single link, the overall loss probability is the smallest under Complete Sharing and the largest under MAM, with that under RDM being intermediate. Expressed differently, Complete Sharing yields the highest link efficiency and MAM the lowest. As a matter of fact, the overall loss probability of Complete Sharing is identical to the loss probability of a single class as computed by the Erlang loss formula. Yet Complete Sharing has the poorest class protection capability. (Note that, in a network with many links and multiple-link routing paths, analysis in [6] showed that Complete Sharing does not necessarily lead to maximum network-wide bandwidth efficiency.) Increasing the degree of bandwidth sharing among the different traffic classes helps increase link efficiency. Such increase, however, will lead to a tighter coupling between different classes. Under normal loading conditions, proper dimensioning of the link so that there is adequate capacity for each class can minimize the effect of such coupling. Under overload conditions, when there is a scarcity of capacity, such coupling will be unavoidable and can cause severe degradation of service to the lower-priority classes. Thus, the objective of maximizing link usage as stated in criterion (5) of Section 1 must be exercised with care, with due consideration to the effect of interactions among the different classes. Otherwise, use of this criterion alone will lead to the selection of the Complete Sharing Model, as shown in Figure 14. The intention of criterion (2) in judging the effectiveness of different BCMs is to evaluate how they help the network achieve the expected performance. This can be expressed in terms of the blocking and/or preemption behavior as seen by different classes under various loading conditions. For example, the relative strength of a BCM can Lai Standards Track [Page 20]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 be demonstrated by examining how many times the per-class blocking or preemption probability under overload is worse than the corresponding probability under normal load. 9. Conclusions BCMs are used in DS-TE for path computation and admission control of LSPs by enforcing different BCs for different classes of traffic so that Diffserv QoS performance can be maximized. Therefore, it is of interest to measure the performance of a BCM by the LSP blocking/preemption probabilities under various operational conditions. Based on this, the performance of RDM and MAM for LSP establishment has been analyzed and compared. In particular, three different scenarios have been examined: (1) all three classes have comparable performance objectives in terms of LSP blocking/preemption under normal conditions, (2) class 2 is given better performance at the expense of class 3, and (3) class 3 receives some minimum deterministic guarantee. A general theme is the trade-off between bandwidth sharing to achieve greater efficiency under normal conditions, and to achieve robust class protection/isolation under overload. The general properties of the two BCMs are as follows: RDM - allows greater sharing of bandwidth among different classes - performs somewhat better under normal conditions - works well when preemption is fully enabled; under partial preemption, not all preemption modes work equally well MAM - does not depend on the use of preemption - is relatively insensitive to the different preemption modes when preemption is used - provides more robust class isolation under overload Generally, the use of preemption gives higher-priority traffic some degree of immunity to the overloading of other classes. This results in a higher blocking/preemption for the overloaded class than that in a pure blocking environment. Lai Standards Track [Page 21]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 10. Security Considerations This document does not introduce additional security threats beyond those described for Diffserv [10] and MPLS Traffic Engineering [11, 12, 13, 14], and the same security measures and procedures described in those documents apply here. For example, the approach for defense against theft- and denial-of-service attacks discussed in [10], which consists of the combination of traffic conditioning at Diffserv boundary nodes along with security and integrity of the network infrastructure within a Diffserv domain, may be followed when DS-TE is in use. Also, as stated in [11], it is specifically important that manipulation of administratively configurable parameters (such as those related to DS-TE LSPs) be executed in a secure manner by authorized entities. For example, as preemption is an administratively configurable parameter, it is critical that its values be set properly throughout the network. Any misconfiguration in any label switch may cause new LSP setup requests either to be blocked or to unnecessarily preempt LSPs already established. Similarly, the preemption values of LSP setup requests must be configured properly; otherwise, they may affect the operation of existing LSPs. 11. Acknowledgements Inputs from Jerry Ash, Jim Boyle, Anna Charny, Sanjaya Choudhury, Dimitry Haskin, Francois Le Faucheur, Vishal Sharma, and Jing Shen are much appreciated. 12. References 12.1. Normative References [1] Le Faucheur, F. and W. Lai, "Requirements for Support of Differentiated Services-aware MPLS Traffic Engineering", RFC 3564, July 2003. 12.2. Informative References [2] Le Faucheur, F., Ed., "Protocol Extensions for Support of Diffserv-aware MPLS Traffic Engineering", RFC 4124, June 2005. [3] Boyle, J., Gill, V., Hannan, A., Cooper, D., Awduche, D., Christian, B., and W. Lai, "Applicability Statement for Traffic Engineering with MPLS", RFC 3346, August 2002. Lai Standards Track [Page 22]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 [4] Le Faucheur, F. and W. Lai, "Maximum Allocation Bandwidth Constraints Model for Diffserv-aware MPLS Traffic Engineering", RFC 4125, June 2005. [5] Le Faucheur, F., Ed., "Russian Dolls Bandwidth Constraints Model for Diffserv-aware MPLS Traffic Engineering", RFC 4127, June 2005. [6] Ash, J., "Max Allocation with Reservation Bandwidth Constraint Model for MPLS/DiffServ TE & Performance Comparisons", RFC 4126, June 2005. [7] F. Le Faucheur, "Considerations on Bandwidth Constraints Models for DS-TE", Work in Progress. [8] W.S. Lai, "Traffic Engineering for MPLS," Internet Performance and Control of Network Systems III Conference, SPIE Proceedings Vol. 4865, Boston, Massachusetts, USA, 30-31 July 2002, pp. 256-267. [9] W.S. Lai, "Traffic Measurement for Dimensioning and Control of IP Networks," Internet Performance and Control of Network Systems II Conference, SPIE Proceedings Vol. 4523, Denver, Colorado, USA, 21-22 August 2001, pp. 359-367. [10] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z., and W. Weiss, "An Architecture for Differentiated Service", RFC 2475, December 1998. [11] Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, "Requirements for Traffic Engineering Over MPLS", RFC 2702, September 1999. [12] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, December 2001. [13] Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering (TE) Extensions to OSPF Version 2", RFC 3630, September 2003. [14] Smit, H. and T. Li, "Intermediate System to Intermediate System (IS-IS) Extensions for Traffic Engineering (TE)", RFC 3784, June 2004. Lai Standards Track [Page 23]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Author's Address Wai Sum Lai AT&T Labs Room D5-3D18 200 Laurel Avenue Middletown, NJ 07748 USA Phone: +1 732-420-3712 EMail: wlai@att.com Lai Standards Track [Page 24]
RFC 4128 BC Models for Diffserv-aware MPLS TE June 2005 Full Copyright Statement Copyright (C) The Internet Society (2005). This document is subject to the rights, licenses and restrictions contained in BCP 78 and at www.rfc-editor.org/copyright.html, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Lai Standards Track [Page 25]

   

[Home] [Full RFC index] [RFC humour] [Our technology]

Copyright © Inter-Corporate Computer & Network Services, Inc.  All rights reserved.
All trademarks and RFC contents are the property of their respective owners.